RhinoGold

Naked edges

hello everyone,  

I developed this ring with flow by surfaces. The result is fine for me but the ring is full of naked edges, what did i do wrong?

Like to here your feedback.

Johan

Views: 280

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by pat schmidt on February 6, 2012 at 2:51am

were there naked edges on your design before you did the flow

Permalink Reply by Johan Kegels on February 6, 2012 at 9:48am

Hi Pat,

Thanks for your replie. Indeed my design had also those naked edge before the flow.

Johan

Permalink Reply by pat schmidt on February 6, 2012 at 12:58pm

than the problem is in how you made your design try remaking them using two curves (inside edge and outside edge ) and extrude them = no naked edges

Permalink Reply by Francisco Rosende on February 6, 2012 at 1:18pm

Hi Johan,

In your pic I see that you has all edges selected  and no only naked edges...

You must select only naked edges for checking

Permalink Reply by pat schmidt on February 6, 2012 at 1:21pm

good observation! I missed that...

Permalink Reply by Johan Kegels on February 6, 2012 at 1:44pm

Thanks  guys for your time,

When i built this design, i made each leaf seperately with two curves, then joined them, offset en then extrude. So i don't understand how i have got those naked edges? Or is this the wrong method.

Johan

Permalink Reply by Francisco Rosende on February 6, 2012 at 5:37pm

Hi Johan,

You must change the window naked edges, so you only see the naked, now you have it displayed all edges, and may have no naked edges.I send you where you change the selection
Regards

Attachments:
Permalink Reply by Johan Kegels on February 6, 2012 at 8:42pm

Hi Francisco,

As you replied , i checked the settings but the result stays the same, all the edges are naked!

Permalink Reply by Francisco Rosende on February 7, 2012 at 11:05am

I am not sure but I think your curves are made in the red layer and that is what you see, the command line still says "select  objects with naked edges" and "select at least 1 objects".
Anyway if you want to upload the file and I'll check to see that fails in the model.

Attachments:
Permalink Reply by Johan Kegels on February 8, 2012 at 2:30pm

Hey Francisco

I checked my design again and you were right, the red color was from my red layer! Thanks for your time!

Johan

Permalink Reply by David Sevilla on February 12, 2012 at 1:13am

Another way I check to make sure my polysurfaces are solid is to do an analize I click on analize then on mass properties and then I click on volume.  It will also tell you if you have naked edges there.  Then you can go to surface tools and use join naked edges command to fix anything needed. 

Permalink Reply by Bokeh on February 21, 2012 at 6:38pm

How best to fix naked edges? Is it the same in Rhino and Rhinogold

thanks

▶ Reply to Discussion

RSS

RhinoGold, 3D jewelry design software | Time to adapt to new technologies | Don't get left behind & Happy Designing

Translate

Notes

2-minutes Survey to improve RhinoGold Render Studio

Hi,

 

The RhinoGold Team is working on the new RhinoGold Render Studio 3.5 and we are willing to know your opinion about it.



We have created a short survey to know your valuable suggestions. Please, click on the next link to be redirected to the survey. It will take no longer than 2 minutes!



Click here



We highly appreciate your ideas and be sure that we will work hard…

Continue

Created by Xavier Rofes Mar 5, 2012 at 3:35pm. Last updated by Xavier Rofes Mar 5.

© 2012   Created by Rafael del Molino.   Powered by

Badges  |  Report an Issue  |  Terms of Service

Sign in to chat!